Which TITAN Pad Heater fits my Engine?

Engine Type (Application)
Oil Liquid Capacity (Qrt or L)
Power Source (AC or DC)
Voltage (Volts)

TH50-1


Oil Pan Heaters

TH50-1

Industrial Diesel Products has been selling engine heaters since 1992.

TITAN Pad Heaters for diesel engine, transmission, and hydraulic heating are distributed worldwide; during the past 20 years shipments have been delivered in over 20 countries.

TITAN Pad Heaters are 0.075" (1.9mm) thin flexible silicone heating pads that are attached to the outside of an oil pan or metal fluid reservoir such as a hydraulic tank or water tank. The pad incorportes a special "hi-tech" peel back adhesive on one side that bonds onto the metal surface. Once installed, the heater pad will never fall off.

An Oil Pan Heater is far superior to a block heater and more efficient as a block heater only "warms" a part of the engine not all the engine.

An Oil Pan Heater "heats" the complete engine starting at the bottom.

The hot oil heats the crankshaft, which in turn heats the connecting rods, pistons and cylinder heads.

TITAN Pad Heaters are supplied with an installation kit and instructions for a complete installation; no special tools or skills are required.

No hoses to cut, frost plugs to remove or loss of antifreeze. 

Remember, heat rises up!

TITAN Pad Heaters can be custom designed for individual commercial applications.

Price in US$$

Width: 3.5 Inches
Height: 1.25 Inches
Weight: 0.5 lbs
Output Power: 50 Watts
Amps: 0.4 amps
Voltage (Volts) 120 volts a.c.
Gas Engine Capacity: 1-3 US Quarts
Diesel Engine Capacity: 1-2 US Quarts
Auto/Manual Transmission: 1-2 US Quarts
Hydraulic Tank Engine Capacity: 2-4 US Quarts
Water Tank Capacity: 8-30 US Quarts
Specific Characteristics:
  • Made in the USA
  • UL recognised component
  • BONDS to Oil Pan or Fluid Reservoir
  • RAISES Oil Temperature to Operating Levels
  • IMMEDIATE Oil Pressure Throughout Engine
  • IMPROVES Crankability
  • EXTEND Starter Motor Life
  • REDUCES Cold Start Wear
  • WARMS Important Internal Parts
  • REDUCES System Warm-up Time
  • NO Maintenance
  • IDEAL for Hydraulic Tanks
  • WILL NOT Burn Out Like Immersion Oil Sump Heaters
  • Electrical cord length 6 feet with sealed three point plug

Three Year Warranty



PERFORMANCE IMAGES

Raises oil temperature 100°f in less than two hours

 


HOW TO

Installation Kit

 

Site Preparation

Take note of the following critical criteria before installaion.

  • TITAN heaters can only be installed on a metal surface; steel, aluminum and cast Iron.
  • The application area must have a smooth flat surface, no bumps, ridges or indentations; the pad must make 100% contact with the surface.
  • Remove dirt, grease, oil and paint from the installation area with a cleaning agent that does not leave any oil film on the surface.
  • Do not trim or cut the TITAN heater pad.
  • Warm the engine to raise the oil pan temperature.
  • The TITAN pad heater has an adhesive backing, do not use any other adhesives to apply the pad.

Incorrect installation of the TITAN pad heater will void the warranty.

Installation

  • Sand and clean the application area.
  • Peel off the backing and warm the pad for three seconds to heat the adhesive; apply the pad to the surface area.
  • Weatherproof the outer edge of the pad with the, supplied, high temperature silicone adhesive.
  • Route the electrical cord with whe aid of the, supplied, cable ties to the location where the plug is to be positioned for connection to the AC extension cord. 

TYPICAL APPLICATION

  • Cars
  • Vans
  • Trucks
  • Cranes
  • Gearboxes
  • Compressors
  • Transmissions
  • Water Pumps
  • Snow Ploughs
  • Hydraulic Rams
  • Generating Sets
  • Marine Engines
  • Aircraft Engines